Engine Tuning

Once we got the engine to run last time we needed a slightly more permenent solution for the fuel delivery and we also needed to figure out how to keep the engine cool durring our tests.

For cooling we instaled a electric water pump. A really nice unit that uses a brushless motor that is sealed in a plastic housing. this motor drives an impeller through a magnetic coupling. Pretty inginous. For the sake of simplisity we used a thermal resivor instead of a radiator and fan. This way we could easily keep the engine in a safe temprature zone. The thermal resivor consists of a large cooler filled with water. The electric water pump continously cerculates the water through the engine. When the water gets to hot we just refill it with cool water.

Josh N. is replacing the intake system.

Here is the engine in one of its first runs. The muffler that we are using is from a RM250F and works quite well. The smoke is from oil that was sitting in the headers. The headers that we are using came of a bike that had blown up... Remember our first engine.

Engine tuning.

After finishing the bulk of the chassis we got the engine, electronics, intake system and exhaust system fitted so we could start doing some engine tuning.

From left to right we have Brett, Josh N. and Eric helping get everything sorted.

Because we are still waiting, now less patiently, for our fuel cell to be welded we needed a fuel source. Ben came up with the simple idea of hooking up to his 300Z fuel system with a long piece of fuel tubing.

After awhile of trouble shooting wiring...

"Hey, do you smell something burning?"

"Yeah, smells like electronics."

We frantically disconnect the battery and pray that the distinct smell of fried electronics was not our MoTeC M4 ECU. After some searching I found that one of our coil-on-plugs had given up the good fight. Lesson learned... if you are not running the engine the coils will burn up.

Pretty spectacular destruction. The laminated metal core was fractured, impressive amount of heat. We replaced the coil and proceeded with more caution.

Pedals

After working on the chassis for about 2 weeks straight now we needed a little change of pace. So we set out to build the pedals for the car. The design work was all done in SolidWorks and some pretty slick stamped steel pedals were the result. The main reason for the development of the pedals is to achive the correct pedal ratio so that the brakes "feel" right. Normal pedal ratios would give the driver a very soft pedal and large pedal travel, undesirable features in a racecar.

Here is the clutch pedal all welded up, yes our car will have a clutch pedal. I can hear teams around the nation gasping as I type. As this car is designed for the non professional driver we felt that the familiar control layout far out weighed the performance benefits from having a narrow chassis.

Here is a close up of the welded brake pedal. The upper half of the photo you can see the Willwood balance bar assembly that has been integrated into our pedal. in the bottom right corner you can see the pivot point, note the teflon bushing.

Here are the finished pedals. Grip tape was applied to the pedal surfaces to increase the drivers confidence.

Here you can see the back side of the clutch pedal with the adjustable travel stop at the bottom. The throttle pedal is a mirror image of the clutch pedal.

Engine Mounts Completed

The rotisserie that the chassis is on really help the welding process. Here we are finishing the motor mount welds and doing some high g testing. We know that the motor mounts are solid to -1 vertical g. Hopefully the last time that the chassis will ever be in this position.

Brett finishing the motor mount welds.

Motor fitted.

Brett testing for driver comfort and taking a much needed break.

Motor and Final Drive Fitting

The chassis is really starting to take shape with almost all of the tubes fitted and tacked into place. The next step is to fit the engine and final drive. The engine needed to be fit with custom tubes because we don't have a model that is accurate enough to allow us to fit the tubes from the model.

Here is Scott completing some of the welds on the chassis.

The engine is placed into the chassis and the front engine mounts are fitted.

The final drive is mocked up to the engine to test its placement.

It fits just like expected. It is nice when things work like expected.

Fuel Cell and Tube fitting

While working on fitting the various tubes on the chassis the sheet aluminum for the fuel cell was cut and bent by Josh N. The fuel cell is a ingenious design that incorporates the stock CBR600RR fuel pump as well as a low pressure lift pump that continuously fills the internal surge tank. We are just waiting for the professional welder to weld the tank.

We are also becoming expert tube copers. As you can see in the following pictures. No gaps here, thank you very much.

By May 9th the chassis looked like this.

Tube Frame Progress

As part of the design constraints for the new chassis we utilized as much of the original design as possible. We needed to spare as much redesign time as possible.

Here you can see the front and main hoops set into place and the first tacks of the new frame. The roll hoops are the same as the hybrid chassis hoops.

Brett fitting the upper frame member in the cockpit.

May 7, chassis is starting to take some recognizable shape.